How To Make An Improvised Camping Lantern

Don’t get caught in the wild without a light, and learn how to make an improvised camping lantern in this straightforward guide!

DIY Camping Lantern You Can Make in a Jiffy

 

What You’ll Need:

  • Kerosene fuel
  • Small glass bottle (syrup or soy sauce)
  • Small cup or container (to pour fuel from)
  • A small funnel
  • Aluminum can
  • Cotton t-shirt
  • Scissors

 Step 1: Prepare the Container

We begin by pouring approximately 5oz. (depending on the size of the bottle you are using) of kerosene fuel into a smaller container. This will make pouring into the funnel much easier and more manageable. Using the cup and funnel, fill your bottle about 3/4’s full. Replace the lid and set aside for later.

Step 2: Make the Camping Lantern Wick

Make the Camping Lantern Wick | How To Make An Improvised Camping Lantern

Next, take an aluminum soda can and using your scissors, remove the top and bottom portions. You can cut using the part where the flat area meets the tapered portion as a guide. Take the remaining piece and cut it in half as shown in the picture. Use caution as the edges may be jagged and sharp. Trim the ends by cutting off only enough to remove any jagged edges. This is what you should have left.

Step 3: Prepare Parts of the Wick

Prepare Parts of the Wick | How To Make An Improvised Camping Lantern

Cut the rectangular piece in half. You will only need one piece for the syrup-sized lantern. This will give you an extra piece to make two, or depending on the size of bottle you use, you may have to use the entire piece of aluminum.

This is the approximate size for the syrup-sized lantern, 2.75″ X 2.75″. Once you have this, set it aside for just a moment.

Step 4: Preparing Fabric for the Wick

Preparing Fabric for the Wick | How To Make An Improvised Camping Lantern

Cut a section of cotton t-shirt out, approximately 5.5″ X 6″.

Preparing Fabric for the Wick | How To Make An Improvised Camping Lantern

Now, take your section of t-shirt and roll it up tightly. This will act as the lantern’s wick.

Preparing Fabric for the Wick | How To Make An Improvised Camping Lantern

Place the rolled-up section of t-shirt and place it on the piece of aluminum at one end. The t-shirt should stick out a quarter inch-sized on one end. You’ll need to roll it as tightly as possible.

Preparing Fabric for the Wick | How To Make An Improvised Camping Lantern

When finished, it should look like this. Don’t let go as it will unravel. Now grab the bottle you previously set aside and remove the lid.

Step 5: Insert Your DIY Wick in the Bottle

Insert Your DIY Wick in the Bottle | How To Make An Improvised Camping Lantern

Insert the t-shirt “tail” into the bottle and continue to thread it in. Once you get to the aluminum portion, you may have to slightly crimp the ends in order for it to go into the bottle. In some instances, the piece of aluminum may be too thick and you may have to trim some off for it to fit in the bottle.

While inserting the t-shirt fabric and piece of aluminum, sometimes a twisting motion aids in getting it to go into the bottle. You want the aluminum to fit snugly in the bottle opening while still being able to move up and down.

Step 6: Make Sure Wick Fits Snugly In

Make Sure Wick Fits Snugly In | How To Make An Improvised Camping Lantern

This is what the completed lantern should look like. When you place the cap back on, simply push the aluminum “wick” down, flush with the bottle opening, and twist the lid on as usual. Make sure you check the bottle for any leakage.

Out of the 6 syrup bottle lanterns I have made, none have leaked. The soy sauce bottle lantern tends to leak slightly. I remedied this by cutting a small piece of cork or rubber and placing on the lid to act as a washer; this seemed to do the trick.

When you are ready to use it, remove the lid and using your multi-tool pliers, grab the aluminum wick and pull it out about ½”. You will need to pull more t-shirt material up through the aluminum as it burns down. Whenever the t-shirt material no longer reaches the kerosene, just pull the wick out and replace it.

Step 7: Light Up Your Improvised Camping Lantern

Light Up Your Improvised Camping Lantern | How To Make An Improvised Camping Lantern

There you have it, an improvised lantern from a syrup bottle. This handy little lantern will be a useful addition to your EDC gear or camping equipment for sure! Remember to exercise caution while working with the cut aluminum, kerosene, and fire!

 

Here’s another great idea for a DIY lantern using olive oil and a mason jar:

No matter what your level of survival expertise is, from newly converted enthusiast to seasoned veteran, improvisation is a must-have skill. However, the ability to take what’s available and create something practical and useful is quickly becoming a lost art. With this simple guide, you only need fuel, and you can always go on a dumpster dive for the rest of the materials to make this improvised camping lantern!

How did your own camping lantern improvisation work out? Let us know in the comments section below!

Up Next: How Camping in the Rain Can Prepare You for a Disaster

For more awesome SHTF survival items, you can’t make at home, check out the Survival Life Store!

Check out 7 Cost-Effective Uses For Shipping Containers Survivalists Should Know at https://survivallife.com/uses-for-shipping-containers/

Follow us on FacebookInstagramTwitterTumblr, and Pinterest!

Placard | How To Make An Improvised Camping Lantern

Editor’s Note: This post was originally published on July 7, 2014, and has been updated for quality and relevancy.